Posted  by 

Adaptronic Select ECU Driver Download

The EMU Black is a class-leading, stand-alone engine management system, designed to operate the most advanced and complex engines available. It is a successor of our proven system, EMU. Throughout EMU’s lifetime we collected lots of data that allows us to substantially improve the device hardware and software.

EMU Black targets race cars, road cars, motorcycles, boats, and stationary engine applications.

The EMU Black controls fueling, ignition and auxiliary systems on 1-12 cylinder engines including those with drive-by-wire throttles and VVT.

It can drive up to 6 passive or 12 smart coils directly and does not require external amplifier/power modules to achieve this. Sophisticated drive-by-wire strategies provide a wide range of throttle control along with advanced plausibility (fault/error) checking for safety.

Free, easy to install firmware upgrades further improve system capabilities (e.g. new strategies, trigger patterns, CAN data streams).

Download Files

. BASE MAPS SECTION

The EMU Black features more built-in value than any other aftermarket ECU. It easily matches the functionality of other stand-alone management systems with multiple inputs and outputs. Unlike many other ECU systems, the EMU Black has built-in wideband lambda input (Bosch LSU 4.2, and LSU 4.9 sensors wire directly in), MAP control connector (4 bar MAP sensor on board), 2 EGT probe inputs and an input to directly connect a Flex Fuel ethanol content sensor. All of this provides greater flexibility, reduces costs and negates the requirement for external or supplemental signal conditioning control systems and the associated wiring that other management systems require.

Adaptronic Select Ecu Driver Download Windows 10

TECHNOLOGY

If you wish to manually install drivers, first download the relevant Master Driver files to your Windows operating system – see links to the right on this page. These are zipped files and once downloaded must be extracted to a folder. Now plug in your lead to your PC in any available USB socket. Adaptronic e420d, 440 and Plug-in (all models) ECUs. To correctly communicate with AiM device it is necessary to set them up using the dedicated Adaptronic software: enter “Special functions layer” and go to Serial “Out” port (Select ECUs) box and select “38400 MODBUS/EMODBUS” option as shown here below.

Dec 02, 2019 Adaptronic Modular ECU eMod009 for S4 RX-7 FC3s. Over 10 million users. Each can be either: Pro Firmware Pack V2. On my first read, I get fresh, correct data. Sell now – Have one to sell? Adaptronic e420d Basic Select ECU. Adaptive Tuner Shell M. This item will ship to United Statesbut the seller has not specified shipping options. Eugene Tuning Software Download Eugene Latest Firmware Eugene Revision History Modular Firmware Revision History Do you have an older ECU? Click Here Installation and Start Up Guides for Modular ECUs Wire in ECUS M1200 M2000 M6000 Plug-in ECUS eMod003 Nissan Silvia eMod004Skyline eMod005S13 S13X S14a S15 eMod.

Ecu

The EMU Black is assembled according to IPC-S-815A standards to ensure high reliability of the product. The device is manufactured on an automated assembly line with optical inspection, automatically tested including burn-in. The PCB board quality and design, special surface coating and IP60 enclosure keeps the device operational in the harshest environments. The components used allow continued operation in a very wide temperature range (AECQ-100 GRADE 2 (-40 to +105˚C).

Adaptronic Select ECU Driver Download

SPECIFICATION

Adaptronic Select Ecu Driver Download Windows 10

GENERAL

Temperature rangeAECQ100 GRADE2 (-40 to +105˚C)
Reverse battery protectionYes, internal
Operating voltage6-22V, immunity to transients according to ISO 7637
EnclosureIP 60, custom CNC machined aluminium
Size (mm) and weight(g)150x72x31, 390
Connectors1 x 24, 1 x 39 FCI Automotive connector
PC communicationUSB (with PC client software), serial, CAN

OUTPUTS

Injector outputs6 protected outputs 5A, low side
Ignition outputs6 outputs 7A(15A peak) (passive & active coils supported)
Aux outputs6 protected outputs 5A, low side
Other outputsFull bridge up to 7A, can be used as separate outputs or 2 H-Bridges
WBO heaterProtected low side up to 5A
CommunicationSerial, CAN BUS 2.0B

INPUTS

Analog inputs9 inputs, resolution 10Bits, 0-5V (protected)
EGT inputs2 for K-Type thermocouple
Knock sensor2 inputs
Oxygen sensorLSU 4.2, LSU 4.9 or Narrow band
Trigger inputs3 (primary, 2 cams) Hall/ VR software selectable
VSS1 (Hall / VR)
Flex Fuel SensorYes
Switch inputs3 inputs, switched to ground

SENSORS

Temperature sensorsIAT, CLT, Oil temperature, AC evap temperature
Pressure sensorMAP, Oil pressure, Fuel pressure (user defined characteristic), AC pressure sensor, Back pressure
Oxygen sensorLSU 4.2 or 4.9 (built in controller), Narrow band, external WBO controllers
SpeedVehicle speed sensor (VR/HALL), Gear sensor (sensor, calculated)

FUELING

InjectorsUp to 8 HiZ injectors (sequential)
Injection angle control0-720 deg, start or end of injections
Battery compensationUser defined, wizard for popular injectors
Fueling strategiesVE based speed density, Alpha N
Air charge temp.Based on IAT and CLT
VE table2 tables 16×20 (Load x RPM), resolution of 0.1%
Individual cylinder trimYes
Staged injectionYes
Additional correctionOxygen sensor corrections, EGT correction (per cylinder), BARO, TPS vs MAP, TPS vs RPM, Warmup, Nitrous, LC, ALS, ASE, Fuel pressure, Knock sensor
Lambda based real time correctionUsing Lambda target table
Acc. / Deceleration enrichmentYes

IGNITION

Ignition outputs6 for passive and active coils (software selectable)
Supported triggersN-1, N-2, N-3, N+1, Multitooth, Subaru triggers, Nissan trigger, Lotus Elise, Audi trigger, Renault Clio Wiliams / Alpine, Colt 1.5CZ, Wrangler
Ignition angle table2 tables 16×20 (Load x RPM), resolution of 0.5 Deg
Per cylinder trimYes
Dwell time battery compensationUsed defined, wizard for popular coils
Odd fire compatibilityApplication dependent
Additional correctionCLT, IAT, TPS vs MAP, Nitrous, Idle, Knock sensor, LC, Pit limiter, ALS, Flat shift, Timers, Acc. enrichment

KNOCK SENSING

Channels2
Resonant frequency range1-20kHz, 3rd order AAF
SamplingIgnition event driven, knock window
ActionsIgnition retard, fuel enrichment, dashboard indication

IDLE CONTROL

Control typePWM solenoids (2,3 wires), drive by wire, stepper motors (bi and unipolar), ignition cut, fuel cut
Control strategyOpen / Close loop , ignition angle control
VE correctionYes, for Alpha-N
CorrectionsAC clutch, coolant fan, analog input

BOOST CONTROL

Boost ref and target tables2 sets 10×10 (TPS vs RPM)
Control strategiesOpen / Closed loop (PID based)
CorrectionsGear, VSS, IAT, EGT

DRIVE BY WIRE

Control strategyAdvanced 3D PID + static friction compensation
Supported throttlesAll with DC motor and current requirement lower than 6.5A

Wizard for 28 popular electronic throttles

PPS to throttle position characteristic3D table
BLIP supportYes
ALS supportYes

TRACTION CONTROL

TC strategyDelta RPM, gear compensation
Torque reductionSpark cut using 3D table (16×20)
Sensitivity control10 position rotary switch

VARIABLE VALVE TIMING

Supported systemsVVTi, MiVec, VANOS, Double Vanos
Number of camshafts2
Control strategyPID based closed loop, CAM angle target tables 12×12

FLEX FUEL

Ethanol content measurementYes
Fuel temperature measurementYes
Tables blendingVE, IGN, Lambda/AFR, Boost, Cranking fuel, ASE, Warmup
Fuel temperature PW correctionYes

SPORT

ALS2 independent ALS setting, DBW support
Shift lightPer gear shift light
Launch controlYes
Gear cutYes (Open loop), DBW blip supported

Source: Switch, load cell, CAN

Pit limiterYes
Rolling anti lagYes

ENGINE PROTECTION

Fail safe values for critical sensorsYes
Dashboard indication of failuresYes, user defined
Over temperature engine protectionYes (oil and coolant), user defined, RPM limit
Low oil pressure protectionYes, user defined, shut off
Fuel pressure protectionYes, fuel dose compensation, RPM limit, engine shut off
High exhaust temperatureAlarm, per cylinder fuel trim, boost limit

CAN BUS

CAN standard2.0B 125, 250, 500, 1000 kbps
Supported CAN DashesECUMASTER, Motec M800 Set 1, Haltech E8 E11v2, Pectel SQ 6, AEM
Supported OEM CAN streamsBMW E46, Citroen C2, Mazda RX8, Ford ST, Polaris RZR, Mini Cooper R53, Fiat 500, Renault Clio, Lotus, Ford Fiesta, Ford ST, EVO X (AYC support)

OTHER

Unused injection outputs can be used as AUX outputYes
Output functionsFuel pump, coolant fan, parametric outputs, nitrous control, PWM 3D table output, AC clutch, main relay, speedometer, tachometer
Password protectionYes, 2 levels
TimersFuel, Ignition, Boost, timers controlled by virtual outputs
Serial dashboard supportAIM, RaceTechnology
AutotuneYes
Built in trigger scopeYes
LoggingReal time logging to PC computer, logging on external loggers (serial / CAN)